Introducing the worlds first vacuum tube ribbon microphone

The R-122V was originally developed in 2001 as a benchmark to test our R-122 designs against. Over four years of additional development, the unique R-122V has evolved into a world class ribbon microphone with unparalleled richness, depth and detail, especially in the midrange frequencies. R-122V recorded tracks reveal a lush-ness that must be heard to be truly appreciated. The R-122V vacuum tube ribbon microphone offers the ultimate in ribbon microphone performance for those who insist on the very best.

The R-122V takes the Royer-pioneered concept of active ribbon microphone technology to an unprecedented level by incorporating vacuum tube electronics into the same proven transducer system used in the venerable R-121 and R-122 ribbon microphones. The high operating voltage of the vacuum tube provides a headroom capability far beyond that capable from a standard phantom power supply. In real-world use, this translates into unmatched clarity, detail and airiness.

The R-122V’s head amplifier consists of a low-noise, triode-connected military grade 5840 vacuum tube. Designed for a wide range of applications, the R-122V offers superb transient response and the drive capabilities only a vacuum tube head amplifier can provide. The circuit is devoid of typical vacuum tube coloration.

The R-122V’s triode-configured cathode follower circuitry enables the microphone to drive long cable runs without sonic degradation or high-frequency loss. This capability is further enhanced by the R-122V's dedicated power supply that provides ample current to the vacuum tube electronics. Induced noise is virtually eliminated by the microphone's fully balanced output that is electrically isolated with a special purpose Jensen output transformer.

Like our phantom powered R-122, the R-122V has far more level than non-powered ribbon microphones and its impedance matching circuitry places a perfect load on the ribbon element at all times. This allows the use of a wide variety of mic preamps without concern for gain and impedance matches, two critical issues with ribbon microphones. All of the R122V's increased output comes from its large, specially designed toroidal transformer, so there is no additional noise associated with the microphone's higher output.

Like all Royer products, the R-122V comes with a lifetime warranty to the original owner (the tube warranty is 10 years). 

Vacuum tube electronics provide high output capability, optimal impedance to the ribbon element and low output impedance
Extremely low self-noise
Operates from a dedicated power supply
High SPL capabilities for electric guitar and percussion instruments
Absence of high-frequency peaks, "ringing" and phase shifts
Ribbon element unaffected by impedance/load, heat or humidity
Very low magnetic leakage
Equal sensitivity from front or back of element
Consistent frequency response regardless of distance
Rear side of mic records slightly brighter when three feet or closer to sound source

Close and distant miking
Strings - solo & sections
Acoustic piano, harp, etc.
Electric and acoustic guitar
Vocals, commercial broadcast, voice over
Brass, horn sections
Drum overheads, room miking
Percussion instruments
Live events-recording and sound reinforcement

Acoustic Operating Principle: Electrodynamic pressure gradient with vacuum tube
electronics.
Vacuum Tube: JAN mil-spec 5840W pentode wired in triode
configuration
Polar Pattern: Figure-8
Generating Element: 2.5-micron aluminum ribbon
Magnets: Rare Earth Neodymium
Frequency Response: 30 -15,000 Hz +/- 3dB
Sensitivity: -36 dB (re. 1v/pa +/- 1 dB)
Self-Noise: < 18 dB
Output Impedance: 200 Ohms, balanced
Rated Load Impedance: 1 K-Ohm
Maximum SPL: >135dB SPL @ 20 Hz
Power Requirements: Plate supply: 135 VDC @2ma, Filament supply: 6 VDC@ 150ma from dedicated power supply.
Dimensions: 206mm L, 25mm W (8 1/8 " L, 1" W).
Weight: 300g (10.9 oz )
Finish: Dull Satin Nickel/Matte Black Chrome optional

Carrying Case for microphone, power supply, cable and shock mount (all included)
Microphone sock
Documentation.

Lifetime to original owner, except tube (10 years) and ribbon element (1 year)

List Price
$2,995.00

Patent Number: 6,434,252